Shenzhen Jia Ronghua Technology Co., Ltd.

Service Hotline400 992 5080

中文
485 Remote Meter
  • Single-phase charge smart meter
  • 2 单相费控智能电能表--.jpg

Single-phase charge smart meter

Type:485 Remote Meter

Introduction:Single-phase fee control smart watt-hour meter, used to measure the rated frequency of 50Hz AC single-phase active energy, to achieve first pay after the power management functions.This product is manufactured by special VLSI and SMT process. The key component...

Service Hotline:400 992 5080

Purchasepk10计划Online consultation

  • Description
  • Parameter

Product use

Single-phase fee control smart watt-hour meter, used to measure the rated frequency of 50Hz AC single-phase active energy, to achieve first pay after the power management functions。
This product is manufactured by special VLSI and SMT process。 The key components and components adopt well-known brand of low power consumption and long life device。 The whole machine adopts a variety of anti-interference technology to improve the reliability and service life of the product。 , The data show that using large-screen Chinese LCD, easy to meter reading。
This product can directly measure the positive and negative active energy accurately and directly, and make multi-rate measurement according to the corresponding rate setting, which can store the total energy and the energy data of each rate on the 12 settlement days. With event logging。 Support 2 year time zone, 2 day timetable, 8 day time, 4 kinds of rates。 At the same time also has infrared and RS485 communication, remote meter reading can be achieved, communication protocol to follow DL / T645-2007。 Its performance indicators in line with GB / T 17215.321-2008 and GB / T18460.3-2001 standards.


Start

At a power factor of 1.0 and a current of 0.4% Ib, the watt-hour meter can be started up and recorded continuously.


Defluction

The meter test output does not produce more than one pulse when the meter is applying 115% of the reference voltage without current in the current line.


Installation, wiring and testing

Watt-hour meter in the factory after passing the test, and seal, you can install and use。
installation
Meter should be installed indoors。 The upper part of the power meter base has a hook screw hole, which can be fixed with a hooking screw; two mounting holes are arranged at the lower part of the energy meter and can be fixed with screws on the wiring board; the bottom plate of the energy meter should be placed on a solid and fireproof wall; About 1.8 meters. Meter installation location as shown below:

Structure dimension drawing

wiring
Meter should be in accordance with the terminal box on the wiring diagram wiring, with copper or copper terminal introduction.


test
This series of power meters are equipped with optocoupler test output port, located at the terminals, as shown in the c, e instructions Department, the wiring is as follows:


TECHNICAL PARAMETER


Normal working voltage: 0.9Un~1.1Un
 Extended working voltage: 0.8Un~1.15Un
Limit working voltage: 0.0Un~1.15Un
 Insulation voltage: ≥2000VAC
Power consumption: ≤1.5W和10VA
 The provisions of the scope of work: -25℃~60℃
Limit working range: -40 ℃ ~ 70 ℃
 Storage and shipping limits:-40℃~70℃
Annual average humidity: ≤ 75%
 Dimensions:160mm×112mm×58mm(remote charge control
30 days of the year (spread in a natural way) up to 95% humidity and up to 85% for the rest of the year
 Net weight: 0.9Kg

specification
model

level of accuracy

 Rated voltage (V)

Current (A)

Pulse constant(imp/kWh)

DDZY1225

2.0

220

40

1600

60

1600

Technical indicators
Rated frequency 50Hz
Basic error (see table below)

Load current

Power factor

Basic error(%)

1。0 level

2.0 level

0.05Ib~0.1Ib

1.0

±1.5

±2。5

0.1Ib~Imax

1.0

±1.0

±2.0

0。1Ib~0。2Ib

0.5L  0.8C

±1.5

±2。5

0。2Ib~Imax

0.5L  0.8C

±1.0

±2。0


Order:Single-phase charge smart meter

  • Name
  • PhoneNumber
  • Email
  • VerifyCode
全天PK10计划两期稳定版 PK10全天计划网 全天pk10计划 北京PK10计划网 PK10在线人工计划 全天PK10计划两期稳定版 北京PK10计划网 PK10计划网 PK10在线人工计划 北京pk10计划